Peavey CS 1200X User Manual

Browse online or download User Manual for Receivers and Amplifiers Peavey CS 1200X. Peavey CS 1200X User Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 2

OPERATIONThe CS 1200X is designed for maximum ease and flexibility of operation. When the unit isinstalled and connected as described in the previous

Page 3 - FEATURES

2. STEREO MODE (BALANCED INPUTS)When conditions require the use of a balanced input at the power amplifier, the XLR connectors(11) on either or both c

Page 4

isolated (no longer connected to anything). In other words, the crossover modules and all associ-ated connectors (as well as the PL-2 transformers and

Page 5 - MAINS POWER SWITCH (5)

mode. Remember, the 4-ohm minimum load must be connected between the red binding posts. Ifindividual loads were connected to each output (as in normal

Page 6 - CIRCUIT BREAKERS (9)

turn really is maximum compression range), the input sensitivity control should be set at Ihemaximum clockwise setting. This is always the best settin

Page 7 - TRANSFORMER RECEPTACLES (12)

normal intermittent applications, low-speed fan operation will provide adequate cooling. Sincethe CS 1200X is a redundant two-channel amplifier, but o

Page 8

The result usually is severe clipping (distortion) of the high-frequency material. In a biamplifiedsystem, the high-frequency material is routed to it

Page 9 - MAINS POWER SOURCE

, 5.6.ule. In this case, the associated XLR connector (11) is now unbalanced as per previousdiscussion. If desired, the parallel unbalanced phone jack

Page 10 - WITH JUMPERS

SPECIFICATIONSCharacteristics:(@ 120 V AC,60Hz)Output Power: (Typical Value)Stereo mode, both channels driven2 ohms, 1kHz, 1% THD4 ohms, 1kHz, 1% THD8

Page 11 - PclSlTl”E

k’requency Response: (Typical Value)Stereo mode, both channels driven+O, -1 dB, 1 W RMS, 4 ohms+O, -0.2 dB @ rated output, 4 ohmsDamping Factor: (Typi

Page 12

Alntended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosurethat may be of sufficient magnitude t

Page 13

CS42OOX PATCH DIAGRAMSChannel ASpeakersChannel A (Shielded)Channel ASpeakersStereo ModeChannel B (ShIelded)PATCH DIAGRAM 1Stereo OperationUnbalanced H

Page 14

THIS LIMITED WARRANTY VALID ONLY WHEN PURCHASED AND REGISTERED IN THE UNITED STATES OR CANADA. ALL EXPORTED PRODUCTS ARE SUBJECTTO WARRANTY AND SERVIC

Page 15

IMPORTANT SAFETY INSTRUCTIONSWARNING: When using electric products, basic cautions should always be followed, including the following.1.2.3.4.5.6.7.8.

Page 16

AWARNING!For optimum performance and reliability DO NOT PRESENT THE AMPLIFIER WITH A SPEAKER LOAD OF LESS THAN 2 OHMS, OR ACOMBINATION OF SPEAKERS THA

Page 17

CHANNEL AlN!wT --SEN!3TlVITYMADE IN U.S.A.CHANNEL 0INPUTSENSITIVITYCS” 12oozPROFESSIONAL STEREO POWER AMPLIFIERDDTTM ACTIVE LEDs (1)The DDTTM active L

Page 18 - SPECIFICATIONS

that particular channel. Operation at power output levels below 100% will naturally be indicatedby lower LED readings. The lowest value indicated is 0

Page 19

AGRILLE (6)The back panel includes the fan opening with protective grille (6), where cooling air is drawninto the amplifier. This opening should never

Page 20 - CS42OOX PATCH DIAGRAMS

MODE SWITCH (10)The mode switch is located on the “back-porch” next to the channel input jacks. This switchconverts the CS 1200X from normal stereo mo

Page 21

amp channel or at the input of the PL-MODULE ELECTRONIC CROSSOVER whenBIAMPING, the (PL-2) transformer must be inserted here. Otherwise a blank plug (

Page 22 - SAVE THESE INSTRUCTIONS!

per channel or 4 ohms BRIDGE mode for any application. Operation at loads of 4 ohms perchannel or 8 ohms BRIDGE mode is more desirable for sustained o

Comments to this Manuals

No comments