Peavey EVH 5150 II User Manual download pdf (Page 7)

POWER AMPLIFICATION

SECTION

RATED POWER AND LOAD:

120 W RMS into 16, 8, or 4 ohms

POWER @ CLIPPING:

(Typically @ 5% THD, 1 kHz, 120 V AC

line)

130 W RMS into 16, 8, or 4 ohms

(Bias must be reduced to measure.)

FREQUENCY RESPONSE:

+0, -3 dB, 50 Hz to 20 kHz @ 100 W

RMS into 8 ohms

HUM AND NOISE:

Greater than 75 dB below rated power

POWER AMP EQ:

Active Presence: +10 dB @ 2 kHz

Active Resonance: +10 dB @ cabinet

resonant frequency

POWER CONSUMPTION (Domestic):

400 watts 50/60 Hz, 120 V AC

(Domestic)

TUBE COMPLEMENT:

6-12AX7 preamp tubes

(1 for clean/crunch, 3 for Lead, 1 for

EFX and 1 phase splitter

4-6L6GC

PREAMP SECTION

The following specs are measured @

1 kHz with the controls preset as follows:

Low and High EQ @ 10

Mid EQ @ 0

Bright out

Lead and Rhythm Posts @ 10

Presence and Resonance @ 0 dB

Nominal levels with Pre Gains @ 5

Minimum levels with Pre Gains @ 10

PREAMP INPUT:

Impedance: Very high Z, 470K ohms

Lead Channel (with channel select in):

Nominal Input Level: -60 dBV,

1 mV RMS

Minimum Input Level: -76 dBV,

.15 mV RMS

Clean Channel (with channel select out):

Nominal Input Level: -30 dBV,

30 mV RMS

Minimum Input Level: -34 dBV,

20 mV RMS

Maximum Input Level: 0 dBV,

1.0 V RMS

(Subtract 24 dB with Crunch switch in.)

EFFECTS SEND:

Load Impedance: 47 k ohms or greater

Nominal Output: -10 dBV, 300 mV RMS

EFFECTS RETURN:

Impedance: Very High Z, 470 k ohms

Designed Level: -10 dBV, 300 mV RMS

PREAMP OUT:

Load Impedance: 47 k ohms or greater

Nominal Output: +10 dBV, 3 V RMS

REMOTE FOOTSWITCH:

Special 3-button unit with LED indicators

(supplied)

Channel select and reverb

SYSTEM HUM AND NOISE @

NOMINAL LEVEL (clean channel):

(20 Hz to 20 kHz unweighted)

Greater than 63 dB below rated power

EQUALIZATION:

Custom Low, Mid, and High passive type EQ

Push Bright (Rhythm Channel only)

+6 dB @ 2 kHz

Push Crunch (Rhythm Channel only)

Increases gain

DIMENSIONS (H x W x D):

10" x 26.625" x 11.75"

(25.4 cm x 67.6 cm x 29.8 cm

WEIGHT:

48.3 lbs. (21.91 kg)

Features and specifications subject to change without notice.

7

5150

®

II

SPECIFICATIONS

TUBE STAGES

LEAD

PRE

RHYTHM

PRE

TUBE STAGE

INPUT

LOW MID HI POST

LOW MID HI POST

TUBE STAGES

PUSH

BRIGHT

PUSH

CRUNCH

FOOTSWITCH

SWITCH

LOGIC

CHANNEL

SELECT

FOOTSWITCH

TUBE BUFFER

SWITCH

LOGIC

FOOTSWITCH

EFFECTS

SEND

RETURN

TUBE STAGES

PREAMP

OUT

TUBE

POWER

AMP

SPEAKER

OUTPUTS

IMPEDANCE

SWITCH

SWITCH

LOGIC

RESONANCE

PRESENCE

LEAD

RESONANCE

PRESENCE

RHYTHM

SIGNAL FLOW BLOCK DIAGRAM

5150

®

II

BLOCK DIAGRAM

1 2 3 4 5 6 7 8 9 10 11 12 ... 27 28

Comments to this Manuals

No comments